特價

樹莓派不斷電系統風扇組

NT$ 388 (含稅)

16 件庫存

描述

Print Friendly, PDF & Email

樹莓派不斷電系統風扇組

The PIco FAN Kit is an Advanced Active Cooling System for the Raspberry Pi ® that can be easy installed on the UPS PIco. It is suitable for all Raspberry Pi® users whose board reaches a high temperature, for whatever reason. There is no need for any additional cabling or Power Supply, as the PIco FAN is directly powered and controlled via UPS PIcosupervising circuits.  A small hand work is needed in order to install the PIco FAN, solder an additional temperature sensor, as also the connector for the PIco FAN to the UPS PIco board. All required parts are included in the kit.

The PIco FAN Kit is equipped with an embedded temperature measurement system that continuously checks the Raspberry Pi® PCB temperature with a dedicated sensor and, according to the measured temperature, the micro controller starts, stops, or regulates the rotational speed of the embedded micro-fan.

Thanks to the Special Air Distribution Slots on the UPS PIco PCB , the PIco FAN cools not only the microprocessor on the Raspberry Pi® board but all the heat-generating devices, as well as the whole Raspberry Pi PCB and UPS PIco.

The embedded microcontroller is easily accessible by the user through the I2C interface and allows reading of the measured temperature, setting of temperature threshold, as well as starting/stopping the embedded micro fan. The PIco FAN in ultra low noise.

The PIco FAN Kit Features:

  • Powered from the J8 (P1) connector of the Raspberry Pi® via UPS PIco
  • PWM FAN speed regulation
  • 1 RED LED based information system (Light Red – hot, Light Red – cold)
  • Full control over the system via I2C interface (The PiCO Interface):
    • Unconditional Fan ON/OFF
    • PWM FAN speed regulation
    • Temperature threshold set/get
    • Current System Temperature read
  • Supports Celsius and Fahrenheit scale
  • Can be used inside of the most of already existing cases

Kit Contents:

  1. Micro Fan with cable
  2. Set of 4 pcs of tree clips required for PIco FAN mounting UPS PIco PCB
  3. Set of 4 pcs of rubber washers required for the PIco FAN mounting UPS PIco PCB
  4. TO-92 Temperature sensor
  5. 2mm PCB connector for the FAN

Case Fitment

The PIco FAN is very low profile, placed on the UPS PIco bottom side, so will fit most cases.

Print Friendly, PDF & Email
  1. 安裝前須將開關切到 OFF 關閉電源,否則容易短路。
  2. 安裝完成確保頂針完全對準排針後再打開電源。
  3. 頂針不導通可以壓一下頂針再鬆開或者用刀劃掉排針的氧化層。
  4. 首次連接電池需要注意 WARNING LED 燈是否亮起,如果 LED 燈亮起,則表示對應的電池接反了,電池接反的情況下禁止充電。
  5. 首次連接電池有可能會沒有電源輸出,需要按一下 BOOT 啟動按鍵或者充一下電啟動電池保護晶片,才會有電源輸出。電源開關需要切到 ON 的位置。
  6. 長時間工作大電流建議不要超過 4A,長時間工作在 5A 狀態下會發熱升溫,注意散熱。
  7. 要使用產品配置的電源充電,使用其他電源有可能輸出電源不穩定導致產品損壞。
  8. 電池正極絕緣墊如果弄掉或壞了,建議不要繼續使用,容易導致短路起火,拆電池時切忌用螺絲起子撬電池正極,容易導致短路,要撬要撬電池負級。
Print Friendly, PDF & Email

鋰電池使用注意事項:

    1. 鋰聚合物和鋰離子電池很不穩定,如果充電或使用不當,可能引起火災,導致人身傷害和財產損失。
    2. 對電池組充電和放電時,切勿正負極接反。
    3. 請勿選用其他劣質充電器或充電板充電。
    4. 請勿混用和使用舊電池和新電池,避免使用其他品牌電池。
    5. 若需另購鋰電池產品,需確保電池規格與鋰電池擴充模組相容,建議採用正規廠商電池較佳,切需要執行老化測試,確保鋰電池能夠穩定安全工作。
    6. 鋰電池具有循環壽命,請在達到使用壽命或使用兩年時(先到為準),將舊電池更換為新電池。
    7. 請妥善放置電池類產品,遠離易燃易爆類物品,遠離兒童,避免因保管不慎,引發安全事故。

您可能也喜歡…