本件是針對樹莓派 CM4 設計的 UPS 工業用擴充模組,內建乙太網、HDMI、USB 和 GPIO 等常用介面,支援透過M.2 B KEY 外接 4G/5G 等無線通訊模組,另支援 RS485、CAN 和 RTC 等有線通訊介面。工業導軌外殼設計,適合應用於構建物聯網閘道、4G/5G 路由器、物聯網資料收集,也可應用於自動化和控制系統中的可程式邏輯控制器等。
售價含稅,隨貨附發票
保固3個月
The PIco FAN Kit is an Advanced Active Cooling System for the Raspberry Pi ® that can be easy installed on the UPS PIco. It is suitable for all Raspberry Pi® users whose board reaches a high temperature, for whatever reason. There is no need for any additional cabling or Power Supply, as the PIco FAN is directly powered and controlled via UPS PIcosupervising circuits. A small hand work is needed in order to install the PIco FAN, solder an additional temperature sensor, as also the connector for the PIco FAN to the UPS PIco board. All required parts are included in the kit.
The PIco FAN Kit is equipped with an embedded temperature measurement system that continuously checks the Raspberry Pi® PCB temperature with a dedicated sensor and, according to the measured temperature, the micro controller starts, stops, or regulates the rotational speed of the embedded micro-fan.
Thanks to the Special Air Distribution Slots on the UPS PIco PCB , the PIco FAN cools not only the microprocessor on the Raspberry Pi® board but all the heat-generating devices, as well as the whole Raspberry Pi PCB and UPS PIco.
The embedded microcontroller is easily accessible by the user through the I2C interface and allows reading of the measured temperature, setting of temperature threshold, as well as starting/stopping the embedded micro fan. The PIco FAN in ultra low noise.
The PIco FAN Kit Features:
Kit Contents:
Case Fitment
The PIco FAN is very low profile, placed on the UPS PIco bottom side, so will fit most cases.
Tall enough to host a wide range of add-on board and slim enough to look cool, the HighPi case sets a new standard for ease of use and versatility. It’s just a fraction of an inch taller than most of the “standard” cases, but designed to perfectly host many add-on boards like HiFiBerry DAC+. The HighPi is designed and made in Canada from high quality ABS material.
Installing or removing the Raspberry Pi PI2B board is astonishingly quick, simple, and secure; all without tools or assembly. One snap action locks the Pi board into the case; the second secures the lid, rattle free. Remove the Pi board and the lid with one-finger-releases for each. Genius!
Whether you’re running a plain Raspberry Pi 2 board or modding it to the max, the HighPi case has your Pi covered. Generous internal room allows HATs, break-out boards, or heat sinks. Vents on three sides double as fly-through cable ports for the GPIO and whatever else you need to connect to. A two-section break-out allows you to choose how much of the A/V side of the case to open up for connectors on attached boards.
This case is one of the first to perfectly accommodate the full line of HiFiBerry audio boards. Use one break-out section for DAC+ and Digi+, and both for the Amp+. There is generous clearance around the RCA connectors for bulky, high-end cables. Achieve the sound you want in a clean case design that fits right, right away.
The HighPi PI2B case can be wall mounted horizontally with two screws for easy removal, or mounted in any orientation including upside-down with four screws from inside the case. When wall mounted horizontally, the A/V and audio cables hang downward from the Pi, improving visual tidiness and reducing the need for support of heavy cables.
HighPi Rasberry Pi Case Features: